Laboratory studies of THGEM-based WELL structures with resistive anodes
arXiv:1310.6183 · doi:10.1088/1748-0221/9/04/P04011
Abstract
In this work we investigate three variants of single amplification-stage detector elements; they comprise THGEM electrodes closed at their bottom with metallic or resistive anodes to form WELL-type configurations. We present the results of a comparative study of the Thick-WELL (THWELL), Resistive-WELL (RWELL) and Segmented Resistive WELL (SRWELL), focusing on their performance in terms of spark-quenching capability, gain variation with position and counting rate, pulse shapes and signal propagation to neighboring readout pads; the study included both 30x30 and 100x100 mm detectors. It was shown that the WELL structures with resistive anodes offer stable operation even in a highly ionizing environment, with effective spark quenching, as well as higher gain than the standard THGEM/induction-gap configuration. Cross talk between neighboring readout pads was shown to be effectively eliminated in the segmented detector with a conductive grid underneath the resistive layer. The latter multiplier should allow for the design of very thin detectors, e.g. sampling elements in digital hadronic calorimeters planned for experiments in future linear colliders.
arXiv commentSubmitted to JINST
References in corpus (17)
- A concise review on THGEM detectors
- Thick GEM-like hole multipliers: properties and possible applications
- Advances in Gaseous Photomultipliers
- Thick GEM-like multipliers - a simple solution for large area UV-RICH detectors
- Position Sensing from Charge Dispersion in Micro-Pattern Gas Detectors with a Resistive Anode
- THGEM operation in Ne and Ne/CH4
- Further evaluation of a THGEM UV-photon detector for RICH - comparison with MWPC
- Investigations of a THGEM-based imaging detector
- First studies with the Resistive-Plate WELL gaseous multiplier
- THGEM-based detectors for sampling elements in DHCAL: laboratory and beam evaluation
- Advances in the Development of Micropattern Gaseous Detectors with Resistive Electrodes
- Beam Studies of the Segmented Resistive WELL: a Potential Thin Sampling Element for Digital Hadron Calorimetry
- Time resolution of a Thick Gas Electron Multiplier (THGEM) - based detector
- Position resolution and efficiency measurements with large scale Thin Gap Chambers for the super LHC
- The Development and Study of High-Position Resolution (50 micron) RPCs for Imaging X-rays and UV photons
- A concept for laboratory studies of radiation detectors over a broad dynamic-range: instabilities evaluation in THGEM-structures
- Sporadic electron jets from cathodes - The main breakdown-triggering mechanism in gaseous detectors
Cited by in corpus (16)
- The Resistive-WELL detector: a compact spark-protected single amplification-stage MPGD
- THGEM gain calculations using Garfield++: Solving discrepancies between the simulation and experimental data
- Gain stabilization in Micro Pattern Gaseous Detectors: methodology and results
- Recent advances with THGEM detectors
- First in-beam studies of a Resistive-Plate WELL gaseous multiplier
- The Resistive-Plate WELL with Argon mixtures - a robust gaseous radiation detector
- The Thick Gas Electron Multiplier and its derivatives: physics, technologies and applications
- Signal Formation in THGEM-like Detectors
- First performance evaluation of a Multi-layer Thick Gaseous Electron Multiplier with in-built electrode meshes - MM-THGEM
- Novel Resistive-Plate WELL sampling element for (S)DHCAL
- On the localization properties of an RPWELL gas-avalanche detector
- Electrical breakdown in Thick-GEM based WELL detectors
- Diamond-like carbon coatings for cryogenic operation of particle detectors
- First results of Resistive-Plate Well (RPWELL) detector operation at 163 K
- Discharge mitigation methods in MPGD-based detectors
- Novel resistive charge-multipliers for dual-phase LAr-TPCs: towards stable operation at higher gains